Danger   The Powerbox PB3000 must be operated with a closed housing.   Before opening the housing, disconnect the PB3000 from the power supply by:    •   turning the switch for the line voltage on the front panel of the PB3000 to the "Off" position.  •   turning the switch for the battery voltage on the back side of the PB3000 housing to the "Off" position.  •   removing the battery fuse (back side of the PB3000 housing).  •   unplugging all power and connection cables.

Caution   To avoid transport damage, Powerbox PB3000 must not be transported with the batteries installed.

Figure 9-2

Front Panel of the PB3000

Figure 9-3

Back of the PB3000

EU:	C39195-Z7001-C11
Switzerland:	C39195-Z7001-C38
Britain:	C39195-Z7001-C32
Australia:	C39195-Z7001-C57
Euro:	C39195-Z7001-C46
Brasil:	For HiPath 3350 and 3550: C39195-Z7001-C121 (IEC 60320 jack, straight)   For HiPath 3300, 3500 and 3800: C39195-Z7001-C191 (IEC 60320 jack, 90° right-angled)

Use the power cable to ground the Powerbox PB3000. Fixed, separate grounding is not required.

Table 9-2

Technical Specifications for PB3000

Powerbox PB3000 / Components	Technical specifications
Powerbox PB3000 - including batteries and LUNA2 power supply	Weight when empty: 7.0 kg Total weight: 21.0 kg (13.22 lb.)
Battery compartment - including 4 batteries	Weight: 12.0 kg
Single battery (12 V / 7 Ah)	Weight: 2.65 kg
LUNA2 power supply	Weight: 2.0 kg   For further information on LUNA2 power supply, see Section 3.2.12 "LUNA2"

Figure 9-4

PB3000 with batteries and LUNA2

Caution   When storing a PB3000 equipped with batteries or if it is inactive for a long period of time, remove the battery fuse (F3: Fuse for battery 16 A/T) at the rear of the PB3000 housing.   Powerbox PB3000 must not be transported be the batteries installed. The batteries must first be removed.

Caution   When storing a PB3000 equipped with batteries or if it is inactive for a long period of time, remove the battery fuse (F3: Fuse for battery 16 A/T) on the rear of the PB3000 housing   Powerbox PB3000 must not be transported be the batteries installed. The batteries must first be removed.

Danger   The only batteries approved for connection are V39113-W5123-E891 (12 V/7 Ah).   The use of other battery types is prohibited.

Old batteries with this symbol are utilizable economic units and must be recycled. Old batteries that are not recycled are to be disposed of as special refuse in accordance with all requirements.

Step	Activity
1.	Turn the switch for the line voltage on the front of the PB3000 housing and the switch for the battery voltage on the back of the PB3000 housing to the "Off" position (see Section 9.1.3.1 "PB3000 Control, Display, and Connecting Elements").
2.	Remove the battery fuse on the rear of the PB3000 housing (see Section 9.1.3.1 "PB3000 Control, Display, and Connecting Elements").
3.	Unplug all of the power and connection cables of the PB3000.
4.	Remove the front panel of the PB3000: to do so, remove the four screws.
5.	Pull the plug-in battery module out of the left housing compartment.
6.	Remove the mounting screw [A] on the battery retainer [B].
7.	Remove the battery retainer and set aside.
8.	Insert the battery carefully and connect it: To do this, slide the eight cable connector lugs [D] carefully onto the two connection contacts on each of the four batteries.
9.	Fix the connection cable into place using cable binders.
10.	Replace the battery retainer and secure the mounting screw.
11.	Push the plug-in battery module into the left housing compartment up to the limit stop.
12.	Screw on the front panel of the PB3000: To do so, tighten the four screws.
13.	Connect all of the power and connection cables of the PB3000.
14.	Insert the battery fuse on the rear of the PB3000 housing (see Section 9.1.3.1 "PB3000 Control, Display, and Connecting Elements").
15.	Turn the switch for the line voltage in the front panel of the PB3000 and the switch for the battery voltage on the back side of the PB3000 housing to the "On" position (see Section 9.1.3.1 "PB3000 Control, Display, and Connecting Elements").

Step	Activity
1.	Set the switches for the line voltage and the LUNA2 voltage on the front of the PB3000 housing to the "Off" position (see Section 9.1.3.1 "PB3000 Control, Display, and Connecting Elements").
2.	Remove the fuse on the rear of the PB3000 housing (see Section 9.1.3.1 "PB3000 Control, Display, and Connecting Elements").
3.	Unplug all of the power and connection cables of the PB3000.
4.	Remove the front panel of the PB3000: to do so, remove the four screws.
5.	Push LUNA2 into the right housing compartment up to the limit stop.
6.	Screw on the front panel of the PB3000: To do so, tighten the four screws.
7.	Connect all of the power and connection cables of the PB3000.
8.	Insert the battery fuse on the rear of the PB3000 housing (see Section 9.1.3.1 "PB3000 Control, Display, and Connecting Elements")
9.	Set the switches for the line voltage and the LUNA2 voltage on the front panel of the PB3000 to the "On" position (see Section 9.1.3.1 "PB3000 Control, Display, and Connecting Elements").

Caution    •   If the Powerbox PB3000 is wall mounted, you must install it in the proper direction and sequence.  •   The battery compartment including batteries and/or LUNA2 power supply must be removed before installation!  •   Wall anchors and screws (not supplied) must be selected according to the wall the device will be mounted on. The head of the screw must be big enough to fit securely behind the mounting bracket! The wall mounting point (wall and screw) must be suitable to support 90kg!

Step	Activity
1.	Drill a hole in the selected wall, insert a wall anchor in the hole, and screw in the respective screw.
2.	Screw the angle brackets (A) and (B) for the PB3000 onto the base of the device.   Note: In the process, pay attention to the precise seat of the angle brackets in the centering recess. These must lock into each other.
3.	Mount the PB3000 with the angle bracket (A) on the screws.
4.	Drill a second hole in the wall for the lower angle bracket (B), insert a wall anchor and attach the angle bracket with a screw.
5.	Reinstall the battery compartment and/or the LUNA2 power supply and reattach the front panel of the PB3000 (see Section 9.1.3.6 "Installing Batteries in PB3000" and Section 9.1.3.6 "Installing the LUNA2 Power Supply in PB3000").   The PB3000 can now be used.

Caution   The battery compartment including batteries and/or LUNA2 power supply must be removed before installation!

Step	Activity
1.	Attach the angle brackets (A), to attach the PB3000 with two screws on both sides (left and right) of the frame of the 19-inch cabinet.   Note: Necessary height units for 19-inch cabinet assembly: 4 HE   (one height unit (HE) corresponds to approx. 1.7''=43 mm)
2.	Attach both angle brackets (B) to the PB3000 with 2 screws on both sides (left and right).
3.	Insert the PB3000 between the angel brackets in the 19-inch cabinet (to the limit stop).
4.	Secure the two angle brackets of the PB3000 each with 2 screws on the frame of the 19-cabinet.
5.	Reinstall the battery compartment and/or the LUNA2 power supply and reattach the front panel of the PB3000 (see Section 9.1.3.6 "Installing Batteries in PB3000" and Section 9.1.3.6 "Installing the LUNA2 Power Supply in PB3000").   The PB3000 can now be used.