3.3.35  
TMANI, TMANI-IM, TMANI-BRA [TMANI8] 
 
NOTE  
Danger of damage to property due to surge voltage. The required lightning protection measures must be taken for this board, see Section 2.1.2 "Lightning Protection".  

Occupation variants of TMANI8  
The TMANI8 for HiPath 3800 can be occupied in the following variants based on a common PCB:
 •   TMANI (S30810-Q2327-X): Fully occupied board, i.e. with call charge filter, call detail recording and jumper for ground start/loop start configuration.
 •   TMANI-IM (S30810-Q2327-X1): Board without call charge filter and call detail recording; only loop start, no ground start.
 •   TMANI-BRA (S30810-Q2327-X82, for Brazil): Board without call charge filter and call detail recording; only loop start, no ground start; Special surge arrestor with varistors.

Features  
 •   Interfaces:
    The TMANI, TMANI-IM and TMANI-BRA boards provide 8 interfaces for the analog trunk connection (MSI: Ground Start [not with IM and BRA] or Loop Start) for HiPath 3800. The ground start function is only used in the U.S. and Canada.
 •   The interfaces for the analog trunk connection support the CLIP feature.
 •   Pulse dialing and multi-frequency dialing
 •   Call detail recording with TMANI:
    The interfaces for the analog trunk connection support call detail recording with 12 kHz and 16 kHz pulses. Call detail recording is selected automatically via the country setting of the system. Call detail recording with 50 Hz pulses is not supported.
   
NOTE  
Call detail recording at 12 kHz and 16 kHz pulses and process changeover for analog trunk interfaces (jumper X100 and X101) are not supported by all country variants for modules.  
    With HiPath 3000/5000 Manager E, call detail recording can be activated and deactivated (Settings menu: Lines/networking ... -> Trunks -> (double-click) Parameters -> MSI flags -> Flags -> Charge module activated).
 •   Silent Reversal:
    "Silent Reversal", which is used to register the beginning and end of an outgoing call in different countries, is also supported. It can be activated with HiPath 3000/5000 Manager E (Settings menu: Lines/networking ... -> Trunks -> (double-click) Parameters -> MSI flags -> Flags -> Silent Reversal).
 •   ÜFS direct inward dialing:
    The Austrian direct inward dialing system ÜFS is not supported.

Installation instructions in the U.S. and Canada:  
According to U.S. and Canadian installation instructions, analog trunks must be connected over fuse elements in compliance with UL 497A or CSA C22.2 No. 226.

Front panel, LEDs  
 Figure 3-98   TMANI8 - front panel, LEDs (S30810-Q2327-Xxx)
 
An additional shielding panel is not required on the front side of this board, because the EMC shield is already provided by the front panel.

Jumper for setting the procedure for analog trunk interfaces  
The procedure for the analog trunk interfaces is set via jumper X100 and X101.
 •   Loop start setting = pins 1-2 closed (default)
 •   Ground start setting = Pins 2 - 3 closed [not with IM and BRA]

LED statuses and their meanings  

 Table 3-134   TMANI8 - LED States
 Red LED  
 Green LED  
 Status  
 Action  
 Off  
 Off  
Board not receiving power or not plugged in correctly.  
Board is out of order.  
Check plug contact on board.  
 On  
 Off  
Board is receiving power and board test is in progress.  
Board is defective if status remains unchanged (board test unsuccessful).  
 
 
Replace board.  
Loadware loading not successfully completed. Board is faulty.  
Replace board.  
Error detected on board.  
Board is deactivated (not applicable to errors detected by test loops) or board was deactivated using HiPath 3000/5000 Manager E.  
Check whether the board was deactivated using HiPath 3000/5000 Manager E. If not, replace board.  
 Flashing  
 Off  
Loadware is being loaded.  
 
 Off  
 On  
Board test completed successfully. Board is OK (idle state).  
 
 Off  
 Flashing  
At least one subscriber line circuit is activated.  
 

Cable and connector assignment  
 •   For connecting to the SIVAPAC connector on the backplane: Table 3-135
 •   For connecting to the connector panels using RJ45 jacks: Table 3-136
 •   For U.S. only: For connecting to the connector panels with CHAMP jack: Table 3-137
 •   For connecting to the connector panels using SIPAC 1 SU connectors: Table 3-138

 Table 3-135   TMANI8 - SIVAPAC Connector Assignment on the Backplane
 Pair  
 a-wire (tip)1  
 b-wire (ring)1  
 SIVAPAC connector  
 TMANI8  
 MDFU-E  
 Notes  
 1  
 wht/blu  
   
 1  
 1a  
 Port 1  
 1a  
   
   
 blu/wht  
 23  
 1b  
 1b  
 2  
 wht/ora  
   
 3  
 2a  
 Port 2  
 2a  
   
   
 ora/wht  
 4  
 2b  
 2b  
 3  
 wht/grn  
   
 5  
 3a  
 Port 3  
 3a  
   
   
 grn/wht  
 6  
 3b  
 3b  
 4  
 wht/brn  
   
 7  
 4a  
 Port 4  
 4a  
   
   
 brn/wht  
 8  
 4b  
 4b  
 5  
 wht/gry  
   
 9  
 5a  
 Port 5  
 5a  
   
   
 gry/wht  
 10  
 5b  
 5b  
 6  
 red/blu  
   
 11  
 6a  
 Port 6  
 6a  
   
   
 blu/red  
 12  
 6b  
 6b  
 7  
 red/ora  
   
 13  
 7a  
 Port 7  
 7a  
   
   
 ora/red  
 14  
 7b  
 7b  
 8  
 red/grn  
   
 15  
 8a  
 Port 8  
 8a  
   
   
 grn/red  
 16  
 8b  
 8b  
 9  
 red/brn  
   
 17  
   
 Free  
   
   
   
 brn/red  
 18  
   
   
 10  
 red/gry  
   
 19  
   
 Free  
   
   
   
 gry/red  
 20  
   
   
 11  
 blk/blu  
   
 24  
   
 Free  
   
   
   
 blu/blk  
 25  
   
   
 12  
 blk/ora  
   
 26  
   
 Free  
   
   
   
 ora/blk  
 27  
   
   
 13  
 blk/grn  
   
 29  
   
 Free  
   
   
   
 grn/blk  
 30  
   
   
 14  
 blk/brn  
   
 31  
   
 Free  
   
   
   
 brn/blk  
 32  
   
   
 15  
 blk/gry  
   
 34  
   
 Free  
   
   
   
 gry/blk  
 35  
   
   
 16  
 yel/blu  
   
 37  
   
 Free  
   
   
   
 blu/yel  
 38  
   
   
1see "Abbreviations for colors" at the start of Section 3.3 "Peripheral boards".

 Table 3-136   TMANI8 - Connector Panel Assignment with RJ45 Jacks
 RJ45 jack  
 TMANI8  
 Notes  
 No.  
 Pin  
 1  
 4  
 1a  
   
 5  
 1b  
 2  
 4  
 2a  
   
 5  
 2b  
 3  
 4  
 3a  
   
 5  
 3b  
 4  
 4  
 4a  
   
 5  
 4b  
 5  
 4  
 5a  
   
 5  
 5b  
 6  
 4  
 6a  
   
 5  
 6b  
 7  
 4  
 7a  
   
 5  
 7b  
 8  
 4  
 8a  
   
 5  
 8b  
 9  
 4  
   
 Free  
 5  
   
 10  
 4  
   
 Free  
 5  
   
 11  
 4  
   
 Free  
 5  
   
 12  
 4  
   
 Free  
 5  
   
 13  
 4  
   
 Free  
 5  
   
 14  
 4  
   
 Free  
 5  
   
 15  
 4  
   
 Free  
 5  
   
 16  
 4  
   
 Free  
 5  
   
 17  
 4  
   
 Free  
 5  
   
 18  
 4  
   
 Free  
 5  
   
 19  
 4  
   
 Free  
 5  
   
 20  
 4  
   
 Free  
 5  
   
 21  
 4  
   
 Free  
 5  
   
 22  
 4  
   
 Free  
 5  
   
 23  
 4  
   
 Free  
 5  
   
 24  
 4  
   
 Free  
 5  
   

 Table 3-137   TMANI8 - Connector Panel Assignment with CHAMP Jack (for U.S. only)
 CHAMP jack  
 TMANI8  
 Notes  
 1  
 1a  
 1 Ring  
 Port 1  
   
 26  
 1b  
 1 TIP  
 2  
 2a  
 2 Ring  
 Port 2  
   
 27  
 2b  
 2 TIP  
 3  
 3a  
 3 Ring  
 Port 3  
   
 28  
 3b  
 3 TIP  
 4  
 4a  
 4 Ring  
 Port 4  
   
 29  
 4b  
 4 TIP  
 5  
 5a  
 5 Ring  
 Port 5  
   
 30  
 5b  
 5 TIP  
 6  
 6a  
 6 Ring  
 Port 6  
   
 31  
 6b  
 6 TIP  
 7  
 7a  
 7 Ring  
 Port 7  
   
 32  
 7b  
 7 TIP  
 8  
 8a  
 8 Ring  
 Port 8  
   
 33  
 8b  
 8 TIP  
 9  
   
   
 Free  
   
 34  
   
   
 10  
   
   
 Free  
   
 35  
   
   
 11  
   
   
 Free  
   
 36  
   
   
 12  
   
   
 Free  
   
 37  
   
   
 13  
   
   
 Free  
   
 38  
   
   
 14  
   
   
 Free  
   
 39  
   
   
 15  
   
   
 Free  
   
 40  
   
   
 16  
   
   
 Free  
   
 41  
   
   

 Table 3-138   TMANI8 - Connector Panel Assignment with SIPAC 1 SU Connectors (Cable for Ports 1 - 16)
 Color Group  
 Pair  
 a-wire (tip)1  
 b-wire (ring)1  
 SU connector  
 TMANI8  
 MDFU-E  
 Patch Panel,
MW8 pin  
 Notes  
 1  
 1  
 wht/blu  
   
 19  
 1a  
 Port 1  
 1a  
 4  
   
   
 blu/wht  
 39  
 1b  
 1b  
 5  
 2  
 wht/ora  
   
 38  
 2a  
 Port 2  
 2a  
 4  
   
   
 ora/wht  
 48  
 2b  
 2b  
 5  
 3  
 wht/grn  
   
 27  
 3a  
 Port 3  
 3a  
 4  
   
   
 grn/wht  
 47  
 3b  
 3b  
 5  
 4  
 wht/brn  
   
 16  
 4a  
 Port 4  
 4a  
 4  
   
   
 brn/wht  
 46  
 4b  
 4b  
 5  
 5  
 wht/gry  
   
 05  
 5a  
 Port 5  
 5a  
 4  
   
   
 gry/wht  
 45  
 5b  
 5b  
 5  
 2  
 6  
 red/blu  
   
 14  
 6a  
 Port 6  
 6a  
 4  
   
   
 blu/red  
 44  
 6b  
 6b  
 5  
 7  
 red/ora  
   
 23  
 7a  
 Port 7  
 7a  
 4  
   
   
 ora/red  
 43  
 7b  
 7b  
 5  
 8  
 red/grn  
   
 32  
 8a  
 Port 8  
 8a  
 4  
   
   
 grn/red  
 42  
 8b  
 8b  
 5  
 9  
 red/brn  
   
 11  
   
 Free  
   
   
   
   
 brn/red  
 31  
   
   
   
 10  
 red/gry  
   
 02  
   
 Free  
   
   
   
   
 gry/red  
 22  
   
   
   
 3  
 11  
 blk/blu  
   
 13  
   
 Free  
   
   
   
   
 blu/blk  
 33  
   
   
   
 12  
 blk/ora  
   
 04  
   
 Free  
   
   
   
   
 ora/blk  
 24  
   
   
   
 13  
 blk/grn  
   
 15  
   
 Free  
   
   
   
   
 grn/blk  
 35  
   
   
   
 14  
 blk/brn  
   
 06  
   
 Free  
   
   
   
   
 brn/blk  
 26  
   
   
   
 15  
 blk/gry  
   
 17  
   
 Free  
   
   
   
   
 gry/blk  
 37  
   
   
   
 4  
 16  
 yel/blu  
   
 08  
   
 Free  
   
   
   
   
 blu/yel  
 28  
   
   
   
1see "Abbreviations for colors" at the start of Section 3.3 "Peripheral boards".

HiPath 3000/5000 V9, Service Documentation, Issue 7   up Top
Disclaimer & Copyright   ID: P31003H3590S100017620   2012-06-25