NOTE   Danger of damage to property due to surge voltage. The required lightning protection measures must be taken for this board, see Section 2.1.2 "Lightning Protection".

Figure 3-58

SLCN (not for U.S.) (S30810-Q2193-X300) - LEDs in the Front Panel

Table 3-64

SLCN (not for U.S.) - LED Statuses

Red LED	Green LED	Status	Action
Off	Off	Board not receiving power or not plugged in correctly.   Board is out of order.	Check plug contact on board.
On	Off	Board is receiving power and board test is in progress.   Board is defective if status remains unchanged (board test unsuccessful).	Replace board.
		Loadware loading not successfully completed. Board is faulty.	Replace board.
		Error detected on board.   Board is deactivated (not applicable to errors detected by test loops) or board was deactivated using HiPath 3000/5000 Manager E.	Check whether the board was deactivated using HiPath 3000/5000 Manager E. If not, replace board.
Flashing	Off	Loadware is being loaded.
Off	On	Board test completed successfully. Board is OK (idle state).
Off	Flashing	At least one subscriber line circuit is activated.

Table 3-65

SLCN (not for U.S.) - SIVAPAC Connector Assignment on the Backplane

Pair	a-wire (tip)1	b-wire (ring)1	SIVAPAC connector	SLCN		MDFU-E	Notes
1	wht/blu		1	1a	Port 1	1a
		blu/wht	23	1b		1b
2	wht/ora		3	2a	Port 2	2a
		ora/wht	4	2b		2b
3	wht/grn		5	3a	Port 3	3a
		grn/wht	6	3b		3b
4	wht/brn		7	4a	Port 4	4a
		brn/wht	8	4b		4b
5	wht/gry		9	5a	Port 5	5a
		gry/wht	10	5b		5b
6	red/blu		11	6a	Port 6	6a
		blu/red	12	6b		6b
7	red/ora		13	7a	Port 7	7a
		ora/red	14	7b		7b
8	red/grn		15	8a	Port 8	8a
		grn/red	16	8b		8b
9	red/brn		17	9a	Port 9	9a
		brn/red	18	9b		9b
10	red/gry		19	10a	Port 10	10a
		gry/red	20	10b		10b
11	blk/blu		24	11a	Port 11	11a
		blu/blk	25	11b		11b
12	blk/ora		26	12a	Port 12	12a
		ora/blk	27	12b		12b
13	blk/grn		29	13a	Port 13	13a
		grn/blk	30	13b		13b
14	blk/brn		31	14a	Port 14	14a
		brn/blk	32	14b		14b
15	blk/gry		34	15a	Port 15	15a
		gry/blk	35	15b		15b
16	yel/blu		37	16a	Port 16	16a
		blu/yel	38	16b		16b

1see "Abbreviations for colors" at the start of Section 3.3 "Peripheral boards".

Table 3-66

SLCN (not for U.S.) - Assignment of Connector Panels with RJ45 Jacks

RJ45 jack		SLCN	Notes
No.	Pin
1	4	1a
	5	1b
2	4	2a
	5	2b
3	4	3a
	5	3b
4	4	4a
	5	4b
5	4	5a
	5	5b
6	4	6a
	5	6b
7	4	7a
	5	7b
8	4	8a
	5	8b
9	4	9a
	5	9b
10	4	10a
	5	10b
11	4	11a
	5	11b
12	4	12a
	5	12b
13	4	13a
	5	13b
14	4	14a
	5	14b
15	4	15a
	5	15b
16	4	16a
	5	16b
17	4		Free
	5
18	4		Free
	5
19	4		Free
	5
20	4		Free
	5
21	4		Free
	5
22	4		Free
	5
23	4		Free
	5
24	4		Free
	5

Table 3-67

SLCN (not for U.S.) - Assignment of Connector Panels with SIPAC 1 SU Connectors (Cable for Ports 1 - 16)

Color Group	Pair	a-wire (tip)1	b-wire (ring)1	SU connector	SLCN		MDFU-E	Patch Panel, MW8 pin	Notes
1	1	wht/blu		19	1a	Port 1	1a	4
			blu/wht	39	1b		1b	5
	2	wht/ora		38	2a	Port 2	2a	4
			ora/wht	48	2b		2b	5
	3	wht/grn		27	3a	Port 3	3a	4
			grn/wht	47	3b		3b	5
	4	wht/brn		16	4a	Port 4	4a	4
			brn/wht	46	4b		4b	5
	5	wht/gry		05	5a	Port 5	5a	4
			gry/wht	45	5b		5b	5
2	6	red/blu		14	6a	Port 6	6a	4
			blu/red	44	6b		6b	5
	7	red/ora		23	7a	Port 7	7a	4
			ora/red	43	7b		7b	5
	8	red/grn		32	8a	Port 8	8a	4
			grn/red	42	8b		8b	5
	9	red/brn		11	9a	Port 9	9a	4
			brn/red	31	9b		9b	5
	10	red/gry		02	10a	Port 10	10a	4
			gry/red	22	10b		10b	5
3	11	blk/blu		13	11a	Port 11	11a	4
			blu/blk	33	11b		11b	5
	12	blk/ora		04	12a	Port 12	12a	4
			ora/blk	24	12b		12b	5
	13	blk/grn		15	13a	Port 13	13a	4
			grn/blk	35	13b		13b	5
	14	blk/brn		06	14a	Port 14	14a	4
			brn/blk	26	14b		14b	5
	15	blk/gry		17	15a	Port 15	15a	4
			gry/blk	37	15b		15b	5
4	16	yel/blu		08	16a	Port 16	16a	4
			blu/yel	28	16b		16b	5

1see "Abbreviations for colors" at the start of Section 3.3 "Peripheral boards".

To guarantee uninterrupted operation of the HiPath 3800, not more than two SLCN boards should be plugged in to a PCM segment. This condition must always be observed. For information on PCM segment distribution, see Section 4.1.5.7 "Distribution of the PCM Highway".   One board slot should be kept free between two SCLN boards to prevent overheating.