5.3.10 Configurable Toll Restriction

5.3.10	Configurable Toll Restriction

Implementing features, see also Manager E Configurable Toll Restriction

Definition

Each user in a communications server can be assigned different toll restrictions. Each time a station attempts to seize a trunk, that station's class of service (COS) is checked (toll restriction). The system distinguishes between 15 different classes of service:

•	0 = no trunk access

•	1 = outward-restricted trunk access

•	2 to 7 = allowed lists

•	8 to 13 = denied lists

•	14 = unrestricted trunk access

The following list describes the classes of service in greater detail.

•	No trunk access Users can make internal calls only. Users can use speed-dialing destinations.

•	Outward-restricted trunk access (incoming authorized) Users can only answer external calls. Users can use speed-dialing destinations. Special networking features, see Section 5.3.10.1 "Incompatibilities When Using the LCR Class of Service (LCR COS) with Trunk Access (COS)"

•	Allowed numbers lists These lists define which numbers stations are allowed to dial. If no numbers are entered in an allowed list, the station functions like a telephone with outward-restricted trunk access.

•	Denied numbers lists These lists define which numbers stations are not allowed to dial. If no numbers are entered in a denied list, the station functions like a telephone with unrestricted trunk access.

•	Unrestricted trunk access Users can answer and set up incoming and outgoing calls without restriction.

The Allowed numbers lists contain the digit sequences which may appear at the start of a call number. The maximum length of the digit sequence is seven digits (0..9, *,#). A maximum of 100 entries can be made in the allowed numbers list no. 1 and the lists numbered 2-6 each contain a maximum of 10 entries.

Model-Specific Data

Subject

HiPath 3800

HiPath 3550

HiPath 3500

HiPath 3350

HiPath 3300

Feature available in

Hardware requirements

Trunk connection

Software requirements

V5.0 or later

V1.0 or later

Number of classes of service

Number of characters in list entries

Total number of allowed lists

Allowed lists, long 100 entries

Allowed lists, short 10 entries

Total no. of denied lists

Denied lists, long
50 entries

Denied lists, short
10 entries

Dependencies/Restrictions

Subject

Dependency/Restriction

System speed dialing

You can use system speed-dialing destinations regardless of the COS.

Class of service

The toll restriction classes of service regulate which denied or allowed lists are used for the stations for each trunk group. The classes of service apply to data and voice stations.

CS/CorNet-N/QSig

If the trunk group for networking is set to communications server (CS), the toll restriction check is not performed if a second trunk access code is not configured.

Classes of service for two networked systems

When there is an external seizure of a station from the satellite CS (with COS 2-13) over the main CS, the main CS's first denied list always does the seizing.

For this reason, keep the first denied line of the main CS free for the assessment of the stations from the satellite CS.

The system keeps COS 0, 1, and 14 of the satellite CS. See also Section 5.3.10.1 "Incompatibilities When Using the LCR Class of Service (LCR COS) with Trunk Access (COS)".

Telephone lock

When the lock code is activated, you can restrict the class of service but not select a higher class of service.

5.3.10.1

Incompatibilities When Using the LCR Class of Service (LCR COS) with Trunk Access (COS)

Trunk access regulates the implementation of toll restriction and the use of lines. Toll restriction verifies the call number dialed by the user and either enables or prevents call setup based on allowed and denied lists.

In the case of outgoing trunk seizure, the following distinctions are made in the case of trunks and PABX lines:

1.	Outgoing seizure via a trunk The class of service must be greater than outward-restricted (allowed list, denied list or unrestricted)

2.	Outgoing seizure via PABX lines

•

LCR is active
Whether toll restriction is performed is configured in the LCR dial plan. If yes, the class of service must be greater than outward-restricted.

•

LCR is inactive
A check verifies whether a second discriminating digit is configured.

If a second discriminating is configured, the class of service must be greater than outward-restricted

If a second discriminating digit is not configured, toll restriction is not implemented, and the class of service must be at least outward-restricted.

In the case of an outgoing connection via a PABX line (CorNet-N / Cornet-NQ / QSIG), the class of service is transferred via a networking protocol (restricted). This facilitates toll restriction for break out to the public network.

As only a restricted class of service transfer is possible, the following translation is implemented:

Class of Service in the PABX

Class of Service Relevant for Stations in the Main System

Internal (0)

Outward restricted trunk access (1)

Allowed lists (2 - 7)

Denied list 1 of the main system (8)

Denied lists (8 - 13)

Denied list 1 of the main system (8)

Unrestricted trunk access (14)

The LCR class of service regulates the implementation of the configured outdial rules. This allows the user to configure whether a station is authorized to use an alternative provider, for example. The LCR class of service is valid for the applicable route table in each case. The sequence of the seizure attempts is configured via the route table.

Class of service verification in the case of call forwarding

For class of service verification in the case of forwarded calls, the class of service of the forwarding station always takes precedence. In such cases, the same rules as described above apply.

HiPath 3000/5000 V9, Feature Description, Issue 10		up

Disclaimer & Copyright	ID: P31003H3590F100017618	2014-02-27