12.2.2  
Recording HiPath 3000 Board Status 
 

12.2.2.1  
Central Control Boards 

RUN LED  
A RUN LED that displays the system's operating capacity is located on the central control board.

 Table 12-2   RUN LED - LED Status Meaning
 RUN LED  
 Meaning  
 Off  
No power  
 On  
Reset switch pressed briefly  
 Off  
Reset switch held down for more than 5 seconds (LED is extinguished to acknowledge that a reload has begun)  
 On  
System boot  
 Off
for 0.1 s  
Load operation: APS in SDRAM, loadware, and card data  
 Flashing
0.5 s on/0.5 s off  
Normal operating state (zero load)1  
 Flashing
0.1 s on/0.1 s off  
MMC removed or defective  
1The flashing rhythm depends on the load. The higher the system load the slower the flashing rhythm.

Options available?  
You can call up the following options using the HiPath 3000/5000 Manager E:
 •   CMA
 •   CMS
 •   LIM
 •   IMODN
 •   MPPI, UAM (only with HiPath 3550, HiPath 3350) or UAMR (only with HiPath 3500, HiPath 3300)
The availability of one of these Announcement and Music Modules is displayed as "Option 5".
The ALUM4 module cannot be displayed.

12.2.2.2  
Power Supplies 

 Tabelle 12-3   Power Supply Status Displays
 Board  
 Status display  
HiPath 3800  
 LUNA2  
The LED displays the operating status (on or off).  
 Powerbox PB3000  
The LED displays the operating status (on or off).  
HiPath 3550, HiPath 3350, HiPath 3500, HiPath 3300  
 PSUP  
The LED displays the 5-V output voltage.  
 UPSC-D, UPSC-DR  
 •   A green LED displays the 5-V output voltage.
 •   A yellow LED displays the additional power of -48-V output voltage provided by an external power supply unit (Powerbox PB3000).
 Powerbox PB3000  
The LED displays the operating status (on or off).  

12.2.2.3  
Peripheral Boards 

Viewing peripheral board status  
You can use HiPath 3000/5000 Manager E or Manager T to view the status of all peripheral boards. Display is limited to the following statuses per board:
 •   Board not inserted
 •   Board defective (not loaded)
 •   Board disabled
 •   Board enabled (active)
 •   Board busy (at least one station or line from this board is disconnected, is being called, or is busy).
For ISDN boards, the status of the reference clock is displayed:
 •   No reference clock
 •   Reference clock for clock generator is created.
When viewing the board status using the HiPath 3000/5000 Manager E, all peripheral boards integrated into the system are presented in a table. The status display is updated every 3 seconds.
With Manager T, you can only view the status of one board at a time. You can also update the status display by pressing a key.
You cannot perform additional activities with the HiPath 3000/5000 Manager E and Manager T while viewing the status of a board.

 Table 12-4   HiPath 3000/5000 Manager E - Example of Status Display of Peripheral Boards
 Slot  
 Board  
 not
inserted  
 Defective  
 Blocked  
 Free  
 Res.  
 Clock  
 source  
 1  
STLS2  
   
   
 X  
   
 X  
 X  
 2  
SLU8  
   
 X  
   
   
   
   
 3  
SLA4  
   
   
 X  
 X  
   
   
 4  
TLA8  
   
 X  
   
   
   
   
 5  
 
   
   
   
   
   
   
 6  
 
   
   
   
   
   
   
 7  
TS2  
   
   
 X  
 X  
   
   
 8  
16SLA  
 X  
   
   
   
   
   
 9  
 
   
   
   
   
   
   
 10  
SLMO24  
   
   
   
 X  
   
   

Locking out and releasing boards and ports  
Using the HiPath 3000/5000 Manager E and Manager T, you can lock out a complete station or trunk module. The lockout prevents renewed seizure after the current connection has finished. Release or lockout settings are also retained after a reset.
The first SLMO/SLU board can be blocked. This action does not block the first two ports. You can block specific ports with the "Block selection" option.
Ports of an IVM or HG 1500 board cannot be locked.
When attempting to lock out the last active trunk, you are subsequently notified that remote service through the service center is no longer possible.

HiPath 3000/5000 V8, Service Documentation, Issue 10   up Top
Disclaimer & Copyright   ID: P31003H3580S100017620   2011-01-24